機械氣動式拉網機mechanical pneumatic pulling machine一．產品用途：product use二．本產品主要用于絲印網版的控制，特別適合制作套色印刷網版，高精度的單雙面電路版。This product is mainly used for control of half-tone screen printing,especcially suitable for making adjustment,high-precision screen double sided circuit.三．產品特點：Product features本產品拉網夾頭及框架全部采用專用鋁合金型材制作，保證受力后不變形。This product pulling chuck and all adopt special aluminum alloy frame, ensure no deformation force.夾頭采用全新設計的首鎖網夾結構，高張力之后不滑網，不松脫。Chuck adopt new design of the lock structure, high tension network clip, not after not slide loose.夾頭可左右滑動，保證張力均勻。Chuck can guarantee slip, or even tension.單面拉網手輪通過齒鏈條同步傳遞動力，保證單面夾頭拉力同步。Single pulling the handwheel through tooth synchronous transmission chain,ensure single-side chuck pull synchronization.頂網采用氣動升降，靈活，可靠。Top network using pneumatic elevation ,flexbility and reliability.四．主要技術參數：main technology parameters: 1.拉網面積：200-1500mm pulling area:200*1500mm 2.最大拉網尺寸：800*1200mm Maximum pulling size:800*1200mm 3.最大張力：﹥45N/cm Max tension:﹥45N/cm 4.外形尺寸：1250*1500*760mm Shape dimension: 1250*1500*760mm5.重量：170KG weight:170KG五．操作步驟：operation steps(1)首先根據網框大小調節拉網的面積，然后將活動腳輪鎖死First, according to the regulation of net frame size, then pulling of locking casters activities（2）選擇合適的網框支架將其放在拉網機上。Choosing appropriate nets box on the pulling on scaffolds(3)調節手輪，使網框尖端之間的距離在5-6mm,以避免在拉網過程中由于網紗張力增大，網框頂住網紗而造成網紗的破裂。Adjust the handwheel, make frames, the distance between the tip at 5-6mm, in order to avoid pulling the net yarn tension due process, gauze net frame resist rupture caused the gauze.(4)拉平網紗，用網夾固定好網紗的邊緣，再慢慢旋轉機上四邊的手輪，使網紗慢慢處于張緊狀態，如此反復，直到網紗的各處張力致相等為止，張力的大小概括網紗的目數和質地而定，網張好后最好用張力計進行最終的檢查，主意；網紗拉力不能一次拉到位，必須分開幾次，比如：拉網力要求40N，先拉到150N，經過最少5分鐘的停留后，才拉到20N如此反復拉網才可。Homer, use gauze net clip fixed at the edge of the yarn tried again, slowly rotating machine shipping, gauze handwheel slowly in the tensioner, repeatedly, until the tension of gauze, the size of the tension is equal to the number of white gauze generalization and texture, and after a good network with the final tension meter, idea, Nets yarn tension can pull in place, must separate several times, for instance: pulling force required to 150N 40N, first, after at least 5 minutes before and after the stay, to 20N so repeatedly. Pulling（5）手輪，使網框上升，注意網框均勻地接觸網紗，然后在網框與網紗相接觸的地方涂上藤黃膠，注意：必須等待膠干以后，方可將網框與網紗一同取下。The handwheel, make net frame, note nets box, then equably catenary yarn in net frame with gauze of connection besmear gambogic glue, note: must wait, can be after the glue dry gauze net frame and together.繃網完以后，扳動換向閥，使手輪回到初始的位置，關閉電源After the nets, stretch, throw reversing valves, make the initial position, close to power手輪；當手輪向左旋轉時，網紗處于張緊狀態，當手輪向右旋轉時網紗處于松弛狀態。 The handwheel, When the handwheel left rotates, the nets yarn at a state, when the handwheel right when rotating gauze is flabby condition.活動腳輪；當要調節拉網機拉網的面積時先要松開活動腳輪，螺絲。Electrically activities;. When should adjust pulling the area is pulling the machine to loosen the screw, casters activities.固定腳；整個拉網機的固定支撐。Fixed foot, The pulling of fixing machines杯頭螺絲；當要調節手輪在機架上的位置時，先要松開此螺絲，以便固定手輪。Cup head screws, When should adjust the handwheel on the frame, the first to loosen the screw so that fixed the handwheel.（6）機架frame（7）網夾；在拉網紗時，用于固定網紗四邊，以便使用網版達到最佳。Nets clip, When used in pulling the yarn, fixed, so use gauze net edition網框支撐架Net frame supporting frame萬向把手，以便于調整好拉網機時，先松開四邊上的萬向把手，以便于調整好拉網機時，使氣缸處于網框四邊上對應中間位置，從而達到網框受力均勻平衡，調好后，再調緊此把手，注意：當在調整拉網機的拉網面積時，一定要先同時松開Ａ，Ｃ或Ｂ，D框?qū)堑乃膫€萬向把手，調好再鎖緊彎向把手。2 the universal handle, in order to adjust to loosen, pulling on the edge of the four hands, in order to adjust the universal, make good pulling the net frame edge four cylinder in the middle, and corresponding net frame evenly balanced, good, after adjustment, note: this hand tightly when adjusted pulling machine pulling, must first area and loosen A and B, C, D box diagonal four universal handle, tuned to lock to handle bent.