? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

?

?

大型汽車廂板壓型設備技術參數：

Big car compartments board molding equipment technical parameters:

?
設備長度7600mm，寬950mm，高1000mm?

Equipment length is 7600 mm, 950 mm wide, 1000 mm

設備動力11千瓦，液壓站動力11千瓦;?軋輥采用軸承鋼(GR15)，鍛打后退火

Equipment power 11 kw, 11 kw power hydraulic stationRoll adopts bearing steel (GR15), annealing after forging

?
底座采用310H鋼

Use 310 h steel base

采用下五上四道校平，確保平整;?采用二次成型式，保證產品的方正和直角，上邊大小都可制作?

Using four leveling on the next five, ensure smooth;Using quadratic type, ensure that the product's founder and rectangular, above size can be made;

軋制材料厚度1.5mm-3mm(也可根據用戶要求設計厚度)

Rolling material thickness 1.5 mm - 3 mm (thickness) can also be designed according to user requirements;

?
軋制C型鋼的寬度為80mm-300mm

The width of the rolling C payments for 80 mm - 300 mm

軋制速度8-9m/min

8 to 9 m/min speed

成型道數：27道?

Forming way: 27

工作電壓380V?

Working voltage 380 v

生產速度8~10米/分

Production speed 8 ~ 10 m/min

?
壓型軸徑：90mm?

Pressed trunnion：90 mm

????
立板20mm?

?

Vertical plate 20 mm

?

傳動方式2寸鏈條傳動

2 inch chain transmission drive way

?
采用新式對接式調節鋼套，簡便、快捷、牢固

Using new type adjustment docking steel sets, is simple, fast and strong

?

設備和產的C型鋼方正，是同行業中調節速度快、沖孔快、切斷快?

C payments made in equipment and founder, is in the industry to adjust speed, punching, cutting off quickly

設備底架 ? ? ? 400H鋼，20側板?

Equipment chassis 400 h steel, 20 sides

夾部分?

Clamp part

液壓夾，夾刀采用Cr12材質，經高溫淬火而成?

Hydraulic clamp, clamp knife is made of Cr12 material, after high temperature quenching and into

成型部分 ?

The molding part

?

? ? ?輥壓成型系統有機架，傳動部件，以及冷彎成型輥輪組等組成，分為數控車床旋轉加工成型，成型效果好，減少輪子之間的摩擦，調試方便，快捷。?
進料導向調節 ? ? ? 彩板進料口處可以自行調整板材的左右進料（手動調解螺絲），是原材料和輥之間保持正確的角度?

? ? ?Roller pressure molding system frame, transmission parts, and the cold bending forming roller wheel, etc, can be divided into numerical control lathe spinning processing molding, molding effect is good, to reduce the friction between the wheels, easy to debug, and fast. Feed direction can adjust the color plate feeding mouth adjust sheet about the mediation screws (manual), the feed is correct between raw material and roll Angle

? ? ? ?工作流程 ? ? ? 開卷-----導向進料-----輥壓成型-----定長切斷-----成品出板（人工上卷----人工操作電器系統設置----按啟動設備正常運轉------達到預先設置的板材尺寸后自行切斷，此設備的壓板成型完成）

? ? ? ?Workflow is -- ?oriented feed - rolling forming -- ?fixed-length cutting off -- ?finished goods out of the plate (artificial roll-up - manually operated electrical system Settings - by the start of the normal operation of equipment -- ?after reaching preset sheet sizes to cut off, the pressure plate forming complete equipment)

? ? ?成型后切斷系統 ? ?切斷系統有切斷機架、切斷刀、液壓油缸控制，按照預定程序自行切斷，無需人工參與?

Cut cut system after molding system has cut off the rack, cutting knife, the hydraulic oil cylinder control, in accordance with the scheduled program to cut off, without human involvement

電控系統?

Electric control system

臺灣臺達PLC,數控系統，變頻調速，實現整體自動化生產，可設置長度，數量、批次等?

Taiwan in PLC, numerical control system, frequency control, realize the overall automation production, can be set length, quantity, batch, etc

計數器?

counter

彩用國產光電旋轉統碼器，A40S6-600-2-12-ACP?

Using domestic photoelectric rotating system code, A40S6-600-2-12 - ACP

液壓系統 ? ? ? 獨立液壓站，提供切斷動力?

Hydraulic system independent hydraulic station, offer to cut off the power

系統誤差 ? ? ? 最大長度誤差為±3mm?

System error maximum length error of plus or minus 3 mm

?

? ? ??注意事項 ? ? ? 電源電壓三項380v 前后左右距離遮擋物應該在1米以上，嚴禁幼兒及老年人靠近，嚴禁手伸入運轉的設備里面 ?

? ? ?Considerations about distance before and after the three power supply voltage 380 v mask should be in 1 meters above, the children and the elderly are strictly prohibited to close to, it is forbidden to reach into the operation of the equipment

? ? ? ? ? ??
? ?大型汽車車廂板機設備：檢查封口質量，根據不同材質，直徑的容器以及生產效率，適當修整“設定按鈕(SETTING BUTTON)鍵，使得封口質量最佳。 將手持感應頭上的插頭插入面板上的插座并旋緊，注意定位缺口。 將電源線的插頭一端插入機箱后板上的插座，另一端插入電源供給插座，請務必使用單相三線制電源。 打開機箱后板上的電源總開關（POWER SW.)按面板電源開關（SWITCHING)鍵，待準備（WARM UP) "綠色指示燈亮，機器就可以工作。 將感應頭放在容器蓋上面，按一下手柄上的啟動按鈕，這時加熱（HEATING)紅色指示燈亮，表示正在加熱，感應頭不要移開，加熱（HEATING)紅色指示燈滅后再移去感應頭，等準備（WARM UP)”綠色指示燈亮或機內蜂鳴器短聲嘟提示后又可以進行下一個容器的封口作業。 按住“設定按鈕（SETTING BUTTON)”鍵，設定為合適值，一般在0.5-2.0秒之間。 選擇平整臺面，放穩機器，可以將機箱腳拉開使機器面板便于觀察?

? ? ? ?Large automobile carriage machine equipment: check the sealing quality, according to the different material, the diameter of the container and the production efficiency, appropriate dressing "set BUTTON (SETTING BUTTON) key, and makes the sealing quality best. Insert the plug of hand-held sensing head socket on the panel and tighten, pay attention to the positioning hole. Insert the POWER cord plug one end of the chassis on the rear panel of outlet, the other end inserted into the POWER supply socket, single-phase three-wire system POWER. Be sure to use to open the case on the rear panel POWER master switch (POWER SW.) press panel POWER switch (SWITCHING), to prepare (WARM UP)" the green light is lit, the machine can work.Put container induction head cover above, click the start BUTTON on the handle, then HEATING (HEATING) the red light is lit, said it was heated, the sensing head don't move, HEATING (HEATING) the red light out and then remove the induction head, such as preparation (WARM UP) "the green light is lit or internal buzzer short sound du tip and then can go to the next container sealing homework. Hold down the" set BUTTON (SETTING BUTTON) "key, set to the appropriate value, generally between 0.5 to 2.0 seconds. Choose flat mesa, steadier machine, chassis feet away the machine panel can be convenient for observation

?

? ? ?服務熱線：13929913092 ? ? ?QQ:2264868104 ? ? ? ?QQ：2951045539